channels sewn

It amazes me how I can knock out a mock-up in an afternoon, but the real deal takes forever. But at last the channels are all sewn.

It may have gone quicker if I had used disappearing ink, or chalk, to mark all the channels instead of my pins and tape system. Maybe next time? I'll have to do tests. 

The next steps are, knot all the loose ends, attach the shoulder straps, put in the grommets, sew the panels together, measure and slide the reeds in, then bind the edges. Whew, I'm out of breath. My goal is to be sewing binding by the end of next week.

breakthrough during back panels

It's nice when you realize you're improving. The little milestone I crossed wasn't really that big, but still exciting to me. I had to rethread the bobbin, and for the first time ever did not have to break out the sewing machine manual to read the steps. Also, when I dropped the bobbin back in to start sewing I didn't have to look at a diagram to see which way the thread spooled out. Hoo-ray. 

OK. Continuing with the back panels.  I laid the panels face-to-face, sewed them together at the center back, pressed the seam flat, then turned the panels right side out and stitched right near the edge of the center back seam.

I was a bit nervous about the channels because they are so long, and the panel so narrow, I had no wiggle room. But I took a breath, decided that after the threading breakthrough I was capable, and they came out OK. 

I can't wait to see this corset from the inside when it's done. 

securing the ends of the thread

You know that heavier bit of stitching when the thread is secured by reversing for a few stitches at the end of a seam? I didn't want that extra bit messing up the rooster. So I sewed each channel and pulled the thread through to the back by threading the front strand on a needle.

Once both threads were together on the back I knotted them.

When the boning is in I'll pull all the loose ends into a nearby channel so they disappear. Look at how neat the front looks now.

Again, extra work, but worth it.

boning and more channels

The channels I've patterned (and sewn) are barely 1/4 inch wide. In theory 3/16 inch plastic boning should fit, but I didn't have any handy. I did however have miles of 2.25 mm basket reed left over from another project. I swear not all the corsets will be boned with cane and reed, but since I haven't bought a single thing yet to make this one I thought I just keep sewing instead of driving to LA to buy supplies. Plus, two reeds measure 5/32 inch wide so they'll fit perfectly. Basket reed it is.

I measured and cut the reeds for the small in between channels and sanded the ends.

After they were slipped in place I could work on the long diagonal channels. Because they have a slight curve to them I made another template and taped it in place.

I couldn't slide boning into these channels when after they were sewn because the ends of the channels are against other seams. So I sewed that first seam, placed two trimmed reeds between the layers next to the seam, held them snug in place, and using a piping foot sewed right up against them. 

The most difficult channels are finished. Once I sew the channels on the other pieces I can start assembling!

channel templates

After the Toile and denim front pieces were basted together it was time to start sewing channels.

First, I figured out the boning placement.

Then I made a template from the bottom of the horizontal stitching by tracing the patten onto a new piece of paper and running a tracing wheel across the line.

I cut the template out, taped it on the fabric, and started sewing.

Once I had that first line I could sew the rest using the presser foot as a guide.

Then I marked the center line with tape and sewed the vertical channels. I got the placement for the next couple of channels by placing the pattern on the fabric, pushing a pin through the starting point, 

lifting the pattern a bit and marking that spot with another pin. I did the same for the end point, then I marked the sewing line with tape.

I sewed down that line, then once down each side, and a few more channels were done. I have to insert boning into these channels before moving on to the next ones so I guess I'd better rustle up some boning.